FEATURES q >155.5 Mbps (77.7 MHz) switching rates q +340mV differential signaling q    5 V power supply
q TTL compatible outputs
q Ultra low power CMOS technology q 8.0ns maximum propagation delay q    3.0ns maximum differential skew
q
Radiation-hardened design; total dose irradiation testing to MIL-STD-883 Method 1019
- Total-dose: 300 krad(Si) and 1Mrad(Si)
- Latchup immune (LET > 111 M eV-cm 2/mg)q Packaging options:
- 16-lead flatpack (dual in-line)
q Standard Microcircuit Drawing 5962-95834- QML Q and V compliant part
q Compatible with IEEE 1596.3SCI LVDS
q
Compatible with ANSI/TIA/EIA 644-1996 LVDS Standard
INTRODUCTION
The UT54LVDS032 Quad Receiver is a quad CMOS
differential line receiver designed for applications requiring ultra low power dissipation and high data rates. The device is designed to support data rates in excess of 155.5 Mbps (77.7 MHz) utilizing Low Voltage Differential Signaling (LVDS) technology.
The UT54LVDS032 accepts low voltage (340mV) differential input signals and translates them to 5V TTL output levels. The receiver supports a three-state function that may be used to multiplex outputs. The receiver also supports OPEN, shorted and terminated (100 Ω) input fail-safe. Receiver output will be HIGH for all fail-safe conditions.
The UT54LVDS032 and companion quad line driver UT54LVDS031 provides new alternatives to high power pseudo-ECL devices for high speed point-to-point interface applications.
Standard Products UT54LVDS032 Quad Receiver
Data Sheet
May 22, 2003
TRUTH TABLE
PIN DESCRIPTION APPLICATIONS INFORMATION
The UT54LVDS032 receiver’s intended use is primarily in an uncomplicated point-to-point configuration as is shown in Figure 3. This configuration provides a clean signaling
environment for quick edge rates of the drivers. The receiver is connected to the driver through a balanced media which may be a standard twisted pair cable, a parallel pair cable, or simply PCB traces. Typically, the characteristic impedance of the media is in the range of 100Ω. A termination resistor of 100Ω should be selected to match the media and is located as close to the receiver input pins as possible. The termination resistor converts the current sourced by the driver into voltages that are detected by the receiver. Other configurations are possible such as a multi-receiver configuration, but the effects of a mid-stream connector(s), cable stub(s), and other impedance discontinuities, as well as ground shifting, noise margin limits, and total termination loading must be taken into account.
The UT54LVDS032 differential line receiver is capable of detecting signals as low as 100mV, over a + 1V common-mode range centered around +1.2V. This is related to the driver offset voltage which is typically +1.2V. The driven signal is centered around this voltage and may shift +1V around this center point. The +1V shifting may be the result of a ground potential difference between the driver’s ground reference and the receiver’s ground reference, the common-mode effects of coupled noise or a combination of the two. Both receiver input pins should honor their specified operating input voltage range of 0V to +2.4V (measured from each pin to ground).
Enables Input Output EN EN R IN+ - R IN -R OUT L
H
X Z All other combinations of ENABLE inputs
V ID  > 0.1V H V ID  < -0.1V L Full Fail-safe OPEN/SHORT or Terminated
H
Pin No.Name Description
2, 6, 10, 14R IN+Non-inverting receiver input pin 1, 7, 9, 15R IN-Inverting receiver input pin
3, 5, 11, 13
R OUT Receiver output pin 4EN Active high enable pin, OR-ed
with EN 12EN Active low enable pin, OR-ed
就算候鸟已南飞
with EN 16V DD Power supply pin, +5V + 10%
8
V SS
Ground pin
Figure 2. UT54LVDS032 Pinout
UT54LVDS032Receiver
161514131211109
V DD R IN4-R IN4+R OUT4EN R OUT3R IN3+R IN3-
1R IN1-2R IN1+3R OUT14EN 5R OUT26R IN2+7R IN2-8
V SS
ENABLE
DATA INPUT
1/4 UT54LVDS031
1/4 UT54LVDS032
+-DATA OUTPUT
Figure 3. Point-to-Point Application
RT 100Ω
Receiver Fail-Safe
The UT54LVDS032 receiver is a high gain, high speed device that amplifies a small differential signal
(20mV) to TTL logic levels. Due to the high gain and tight threshold of the receiver, care should be taken to prevent noise from appearing as a valid signal.
The receiver’s internal fail-safe circuitry is designed to source/ sink a small amount of current, providing fail-safe protection (a stable known state of HIGH output voltage) for floating, terminated or shorted receiver inputs.
1. Open Input Pins. The UT54LVDS032 is a quad
receiver device, and if an application requires only 1, 2
or 3 receivers, the unused channel(s) inputs should be
mvleft OPEN. Do not tie unused receiver inputs to ground
or any other voltages. The input is biased by internal high
value pull up and pull down resistors to set the output to
a HIGH state. This internal circuitry will guarantee a
HIGH, stable output state for open inputs.2. Terminated Input. If the driver is disconnected (cable unplugged), or if the driver is in a three-state condition, the receiver output will again be in a HIGH state, even with the end of cable 100Ω termination resistor across the input pins. The unplugged cable can become a floating antenna which can pick up noise. If the cable picks up more than 10mV of differential noise, the receiver may see the noise as a valid signal and switch. To insure that any noise is seen as common-mode and not differential, a balanced interconnect should be used. Twisted pair cable offers better balance than flat ribbon cable.
3. Shorted Inputs. If a fault condition occurs that shorts the receiver inputs together, thus resulting in a 0V differential input voltage, the receiver output remains in a HIGH state. Shorted input fail-safe is not supported across the common-mode range of the device (V SS to 2.4V). It is only supported with inputs shorted and no external common-mode voltage applied.
ABSOLUTE MAXIMUM RATINGS 1(Referenced to V SS )
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other condit
ions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175°C during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL PARAMETER
LIMITS V DD DC supply voltage -0.3 to 6.0V V I/O Voltage on any pin -0.3 to (V DD  + 0.3V)T STG Storage temperature -65 to +150°C P D Maximum power dissipation    1.25 W T J Maximum junction temperature 2+150°C ΘJC Thermal resistance, junction-to-case 310°C/W
I I
DC input current
宝贝去哪儿mv±10mA
SYMBOL PARAMETER
LIMITS V DD Positive supply voltage    4.5 to 5.5V T C Case temperature range -55 to +125°C V IN
DC input voltage, receiver inputs DC input voltage, logic inputs
2.4V
0 to V DD  for EN, EN
DC ELECTRICAL CHARACTERISTICS 1(V DD  = 5.0V +10%; -55°C < T C  < +125°C)Notes:
1. Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground.
2. Output short circuit current (I OS ) is specified as magnitude only, minus sign indicates direction only. Only one output should be shorted at a time, do not excee d maximum junction temperature specification.
3. Guaranteed by characterization.
4. Device tested at V CC  =
5.5V only.
SYMBOL PARAMETER
CONDITION
MIN MAX
UNIT V IH High-level input voltage (TTL)  2.0
V V IL Low-level input voltage (TTL)
0.8V V OL Low-level output voltage I OL  = 2mA, V DD  = 4.5V 0.3V V OH High-level output voltage I OH  = -0.4mA, V DD  = 4.5V    4.0V I IN
Logic input leakage current
Inputs, V IN  = 0 and 2.4V, V CC = 5.5Enables = EN/EN= 0 and 5.5V, V CC = 5.5
-10-10
黄义达 微光
+10+10
µA
V TH 3Differential Input High Threshold V CM  = +1.2V +100mV V TL 3Differential Input Low Threshold V CM  = +1.2V -100mV I I Receiver input Current V IN = 2.4V
-10+10µΑI OZ 4Output Three-State Current Disabled, V OUT  = 0 V or V DD -10+10µΑV CL Input clamp voltage I CL  = +/-18mA -1.5  1.5V I OS 3Output Short Circuit Current Enabled, V OUT  = 0 V 2-15
-130mA I CC 4Loaded supply current receivers enabled
EN, EN = V DD  or V SS Inputs Open 11
mA
I CCZ 4
Loaded supply current receivers disabled
EN = V SS , EN = V DD Inputs Open王祖蓝身高
11
mA
AC SWITCHING CHARACTERISTICS 1, 2, 3, 4(V DD  = +5.0V + 10%, T A  = -55 °C to +125 °C)
Notes:
1. Channel-to-Channel Skew is defined as the difference between the propagation delay of the channel and the other channels in the same chip with an event on the inputs.
2. Generator waveform for all tests unless otherwise specified: f = 1 MHz, Z 0 = 50Ω, t r  and t f  (0% - 100%) < 1ns for R IN  and t r  and t f  < 6ns for EN or EN.
3. C L  includes probe and jig capacitance.
4. Guaranteed by characterization.
5. Chip to Chip Skew is defined as the difference between the minimum and maximum specified diffe
rential propagation delays.
SYMBOL PARAMETER
MIN MAX UNIT t PHLD Differential Propagation Delay High to Low CL = 20pf (figures 4 and 5)
1.08.0ns t PLHD Differential Propagation Delay Low to High CL = 20pf (figures 4 and 5)
1.08.0ns t SKD Differential Skew (t PHLD  - t PLHD ) (figures 4 and 5)0  3.0ns t SK14Channel-to-Channel Skew 1 (figures 4 and 5)0
3.0ns t SK24Chip-to-Chip Skew 5 (figures 4 and 5)7.0ns t TLH 4Rise Time (figures 4 and 5)  2.0ns t THL 4Fall Time (figures 4 and 5)
2.0ns t PHZ 4Disable Time High to Z (figures 6 and 7)20ns t PLZ 4Disable Time Low to Z (figures 6 and 7)20ns t PZH 4Enable Time Z to High (figures 6 and 7)20ns t PZL 4
Enable Time Z to Low (figures 6 and 7)
王丽坤跳水露卫生巾20
ns